A peptide certificate of analysis is a laboratory document that describes one batch of one product. It is not a brochure, not a brand promise, and not transferable between vials. The whole point of it is that a stranger can pick it up and check four things without a chemistry degree.

So this page shows what a real certificate contains, how to match it to the vial in your hand, and what the four most common fakes look like. Then it covers the limit nobody mentions: what even a genuine certificate cannot prove.

What a peptide certificate of analysis should contain

Six fields do the work on a peptide certificate of analysis. If any of them is missing, the document is decoration rather than evidence.

FieldWhat it should sayWhy it matters
Batch or lot numberThe same code printed on your vialWithout a match, the certificate describes some vial rather than yours
Identity testMass spectrometry or LC-MS, with the expected massConfirms the molecule, not just that something pure is present
PurityHPLC percentage, plus the method and columnA percentage with no method is a number without a measurement
Peptide contentNet peptide content, as a percentage or mg per vialPurity and content are different, and the gap is where the mass hides
Test dateThe date the batch was analysedA certificate older than the vial is a certificate for another run
LaboratoryA named laboratory, ideally with an accreditation numberAn unnamed lab cannot be checked, so the claim cannot be checked either

Purity is not peptide content

This is the single most useful thing to understand about a peptide certificate of analysis, and almost nobody explains it on a product page.

HPLC purity measures the peptide fraction: of all the peptide material in the vial, how much is the target sequence. Net peptide content measures the whole mass: of everything in the vial, how much is actually peptide rather than water, counterions or residual solvents.

Therefore a vial can be 98% pure and still contain noticeably less peptide than the label states. The rest is salt and moisture, which are normal in lyophilised product and perfectly legal. They simply are not the drug.

MeasureWhat it tells youWhat it hides
HPLC purity (area %)How much of the peptide material is the right sequenceWater, counterions and salts, which add mass without adding peptide
Net peptide content (%)How much of the vial’s mass is actually peptideNothing much, but it says less about impurity profile
Mass confirmationThat the molecule is the one you orderedQuantity, purity and sterility

A good certificate reports both. A weak one reports only purity, because 99% sounds better than 99% pure at 82% peptide content.

What HPLC and mass spectrometry each tell you

  • HPLC separates and quantifies. It pushes the sample through a column and measures what comes out, which gives you the percentage of the main peak. It says nothing about what that peak is.
  • Mass spectrometry identifies. It measures molecular mass, which is how you tell TB-500 from a related fragment or a peptide that is one amino acid short.
  • Together they answer two questions. Is it the right molecule, and how much of the sample is it? Either one alone leaves the other open.

That is why a certificate showing only a purity percentage is incomplete rather than suspicious. It is half a document, and the half it is missing is the half that would catch a mislabelled vial.

How to match a certificate to your vial

  1. Find the batch code on the vial. It is usually printed on the label or the crimp, and it is the whole basis of the check.
  2. Check that the same code appears on the document. If the numbers differ by a digit, the document belongs to another run.
  3. Check the product name and strength. A 5 mg certificate for a 10 mg vial is not a match, even when the code looks right.
  4. Check the test date against the manufacturing date. Analysis should follow production, not precede it.
  5. Check the methods are named. HPLC with a stated column and wavelength, and mass spectrometry with an expected value. “Tested by our lab” is not a method.

That is the whole check for a peptide certificate of analysis: five minutes, no equipment, and it catches most of what goes wrong. The failure mode is not a clever forgery. It is a genuine certificate for a different batch, reused across a whole catalogue because nobody at the shop bothered to update the page.

The four fake patterns

PatternWhat you seeWhat it means
No batch referenceA certificate with a product name and a purity figure onlyIt cannot be tied to anything you bought
Recycled screenshotThe same image across every product, or across yearsOne analysis, presented as many
Purity with no method99.4% and nothing elseNo measurement described, so no measurement to trust
Unnamed laboratory“Third party tested”, no lab name, no accreditationNobody can verify the claim, including the seller

How to check the laboratory itself

A named laboratory is better than an unnamed one, and an accredited laboratory is better again. Accreditation to ISO/IEC 17025 means an external body has assessed the lab’s methods and competence, and those bodies publish directories you can search.

So the check is straightforward. Take the lab name from the certificate, look for its accreditation number, and search the accreditation body’s public directory. If the lab is not listed, or the certificate is outside the lab’s accredited scope, the claim is weaker than it looks.

Be reasonable about this. A small lab without accreditation can still produce an honest HPLC trace. But the further you go from an accredited lab, the more of the certificate you are taking on trust, and trust is the thing a certificate exists to replace.

What a certificate cannot tell you

  • Sterility. Unless the certificate states a sterility test, the product is not sterile. Most research peptides do not carry one.
  • Safety for human use. No certificate makes an unapproved peptide approved. Our guide to research grade peptides covers what that label actually means.
  • That the seller stored it properly. A certificate describes the batch at the lab, not the parcel in a hot van.
  • That the whole catalogue is tested. One certificate proves one batch. It says nothing about the next one.

Keep the peptide certificate of analysis with the vial, and keep it after the vial is gone. If a batch is later withdrawn, the code on that document is the only record of what you actually had.

FAQ

What is a peptide certificate of analysis?

It is the laboratory document that describes one batch: identity, purity, peptide content, methods and the lab that ran them. A peptide certificate of analysis exists so a buyer can check a specific vial rather than a brand claim.

How do I know if a peptide certificate is real?

Match the batch code to your vial, check that the methods are named, and confirm the laboratory exists and is accredited. Most bad certificates fail the first test.

What purity should a peptide certificate show?

Most reputable suppliers publish figures in the high nineties by HPLC. A number means little without the method beside it, and nothing without the peptide content figure next to it.

Why does peptide content matter more than purity?

Because purity ignores water and counterions. A vial that is 98% pure can still contain well under the stated peptide mass, which is what you are actually buying.

Do I need mass spectrometry on the certificate?

You want it. HPLC confirms how much of a substance is present, while mass spectrometry confirms which substance it is.

Can a certificate prove a peptide is safe?

No. A certificate describes composition for a batch. The document says nothing about human safety, and most research peptides have no human safety data at all.

How old can a certificate be?

The date should match the batch you hold. A certificate dated years before your vial was produced describes a different run, whatever the product name says.

What if the seller will not send a certificate?

Then you have no way to check anything, and the price is the only information on offer. That is the point to stop.

The bottom line

A peptide certificate of analysis is the only document in this market that you can check without trusting anyone. Batch number, identity, purity, peptide content, methods, laboratory: six fields, five minutes.

Because most certificates fail on the batch match rather than on anything technical, the first check is also the most useful one. And because purity and peptide content measure different things, reading both is what separates a real specification from a reassuring number.

Last reviewed: November 2026 by Julian Hart.

This page is educational and is not medical advice, and it does not endorse any supplier. A certificate describes composition, not safety, and no document makes an unapproved peptide legal for human use. For the compounds themselves, see the guides on BPC-157 and TB-500, and the rest in the peptides section.

Sources

  1. Ascent Sciences. Net peptide content vs HPLC purity: the difference between the peptide fraction and the fraction of total mass.
  2. Tide Labs. Purity vs net peptide content: how counterions and moisture adjust the gross weight.
  3. KMD Analytical. Purity versus net peptide content: why purity will not catch a shortfall in peptide mass.
  4. Absolute BioLab. How to read a peptide certificate of analysis: batch matching, HPLC purity, mass spectrometry and evidence gaps.
  5. ANAB (ANSI National Accreditation Board). ISO/IEC 17025 testing laboratory accreditation.
  6. UKAS. Laboratory accreditation to ISO/IEC 17025.
  7. CASRAI. How to verify a supplier’s ISO 17025 accreditation: finding the accreditation body and checking the public directory.
Categories: Steroids

Julian Hart

Julian Hart writes the peptide and hormone guides on bodybuildingweights.net. He has trained clients for 20 years, and peptides and dosage protocols have been his focus for most of that time. At 55 he still trains, which is why a lot of what he writes is aimed at lifters who are no longer 25: recovery, joints, bloodwork and long-term health rather than one cycle. The approach is the same in every guide. Start with the primary literature, say plainly what it does and does not show, and mark the difference between human trial data and animal or mechanistic research. Where the evidence is thin, the guide says so instead of filling the gap with confident language. That means dosing and reconstitution maths worked through step by step, half-life and storage tables, side effect sections that separate what trials reported from what gets repeated on forums, and straight answers about what a certificate of analysis does and does not prove. He is not a doctor and nothing on this site is medical advice. The guides explain what the research says and make the practical questions easier to reason about. Anything involving dosing, bloodwork or a health condition should be discussed with a qualified clinician. Guides are reviewed quarterly and each one shows the date it was last checked. Reach Julian at [email protected].